Recent content by Bearhawk Aircraft

  1. Bearhawk Aircraft

    New AXIS Light IFR panel

    Breakfast of champions right there.
  2. Bearhawk Aircraft

    Engineering Notice from Bob Barrows - November 2026 - Each Builder Should Have a Serialized Set of Plans

    Just to clear a few things up here. Each kit we ship from Bearhawk Aircraft Inc. will have a serial number provided with your shipment. This serial number is kept in our system and will be used to issue safety alerts, service bulletins or your bill of sale at the time of registration. - For...
  3. Bearhawk Aircraft

    Windshield to upper channel

    Hey Tom, Depending on how the windshield came out of the mold, a small amount of sanding on the top windshield flange will help with the fitment a bit. I would not recommend trimming your top flange, typically the flange line on the windshield will be out of Chanel by about a 1/4- 1/2in.
  4. Bearhawk Aircraft

    Bearhawk 4? or 5? with IO540-D4A5

    The Five airframe compared to the Four airframe is less than 30 pounds heavier. The IO540-D4A5 is our small engine option on the Five and big option on the Four. That being said you will have an airframe that is a few pounds heavier empty but with a much more effective tail and great...
  5. Bearhawk Aircraft

    Bearhawk Patrol Belly Pod

    @500AGL Boo your no fun.
  6. Bearhawk Aircraft

    Drilling Axle Nut Cotter Pin

    Mark the end of the axle after nut is torqued. measure the inset of the hole, or where you want the center of your cotter pin to go. Remove wheel drill with #40 then step up to the proper size.
  7. Bearhawk Aircraft

    Interior Lighting

    Cargo light is not a horrible idea but when doing a factory panel all lswitches are back lit and Efis is a screen so no cockpit lighting is required.
  8. Bearhawk Aircraft

    Landing Gear

    Each Beahawk model has a different landing gear leg. They are not interchangeable between models
  9. Bearhawk Aircraft

    Looking for advice for new plane adjustments

    If you don't have an EGT reference I would get that, you are looking for a 1250 degree EGT in climb out. - If you are lean in climb temps will climb very fast. If it is an overhaul motor, you could potentially have a bead internal configuration if not done by a reputable shop, mis match rings...
  10. Bearhawk Aircraft

    Flying Wires Question

    Flip them around, the short side goes to the bolt, long to the wire.
  11. Bearhawk Aircraft

    N62588 Phase 1 Flight Testing

    Expect to see a 3mph reduction in stall speed as well as increased aileron control at high AOA.
  12. Bearhawk Aircraft

    Oil Cooler location for an IO540

    Another consideration here from our experience and why we recommend larger coolers than historically thought necessary is the high altitude operation side of things. When operating at 10-15k feet, which we routinely do in the Five, air gets thin and when running high EGTS ROP oil temps can creep...
  13. Bearhawk Aircraft

    Thoughts on priming stringers.

    Stringers are 6061 they will not corrode for a long time. The green primer in the wings is used mainly due to the 2024T3 construction which is a stronger alloy, but less corrosion resistant thus demanding the use of primer. We do not prime stringers on factory built aircraft.
  14. Bearhawk Aircraft

    Bearhawk Tailwheels Tundra Tailwheels are finally Ready

    The tundra tire was changed to a square profile tire to eliminate shimmy issues experienced in the past. The square profile is much more tolerant of camber change when aircraft is loaded or empty. The profile is 2in smaller in diameter but the same width profile as the previous tundra. This...
  15. Bearhawk Aircraft

    Cowl exit

    Recommended is 30 degree angle 3in lip
Back
Top