Search results

This is where my servo ended up.

I’ve been hemming and hawing about where to mount them. I think I just fingered it out. Thanks.

Thanks for the input! Our current aircraft has an electric trim on/off switch. It’s a great option.

I installed the left windows. Actually I did it several times! I ended up creating two C channels that were 1.5” x .625” x 1.5”. I notched them to clear the stand off tabs for the window frames. That was the easy part. The curved part of the “D” window was the hard part. I tried several...

1. I’m just about ready to start covering my BH5. I have the horizontal stab set to -2 degrees. Do I need to set all the flying wires and strut prior to removing the tail feathers to cover? 2. Has anyone installed the Ray Allen (T3) servo and maintained the manual trim? I’d like to have both...

Mark I ran my aux fuel tank lines a little to close to the lower wing skin. Two spots that have fittings I can’t get a bucking bar into. They both required 4-4 rivets. I did use the MK319BS in the couple spots that I couldn’t get th that used 3-3.5 rivets.

I ordered both. Thanks!

It looks like the factory that made the Chery Max 3212 burned last year. I’m building a 5 and I’m riveting the lower skin on. There are a couple spots that the manual suggests the 3212 because you can’t get a bucking bar in there. Anyone have a suggestion for an alternative? Thanks, Nick

I’m installing my landing lights in my BH5. I got the mounting brackets from Virgil for the Flyled Taildragger lights. Did anyone use any particular angle for your lights? Mine and plumb with the wing at about 11.5 degrees nose up. The lights have two LEDs that point down as taxi lights and 5...

I’m almost ready to close up the left wing. I have a heated pitot tube (Dynon), fuel transfer pump and WAT Blaze position/Nav/Strobe lights, and Flyleds Taildragger Pulse landing/taxi lights. The install directions suggest wire and AC 43 has a section to determine gauge based on power and...

I’m installing the nut plates for the main and aux tank covers. The first 4 from the leading edge moving aft I can’t get my drill in there to drill the holes. Any advice? The first one will be difficult to install the rivet without drilling out the factory installed rivets to create some room...

I’ve got the templates for the strut penetrations on the lower cowl extension. I’m just not sure where to place them. I’d imagine it’s measured from station C. Anyone have some guidance? Once the boot cowl is finished I’m going to put the fuselage aside and start on the wings. The wing manual...

I was considering using something to increase the friction on the pedals/brakes. Though maybe bed liner. Anyone else do this? Thx!

Anyone going? We are 160 hours into our build and I don’t think we will be finished in time. We plan to go and camp either in GA camping or Vintage. We’ll be in a 1969 Baron, N100GM. It’s our first time going.

I’ve leveled the fuselage at the wheels. When I put the level on the vertical stabilizer it is .9 degrees off. I’d like to check the angle of incidence and make sure the horizontal stabilizer is level and perpendicular to the vertical stabilizer. I’m sure I could pull the vertical stab plumb...

How do the two elevators connect? Is there a pin that goes through the fuselage and into the bearings? The “Elevator Bearing Kit” has 4 bearings. Two fit in the elevator tube, I’m not sure where the other two go.

Just started a QB 5 kit. I know Virgil is working on improved directions which will be done just after I finish with my luck. 1. Is there a list of what fastener goes where? 2. How about torque values? Thankfully Aircraft Spruce is drivable from my shop. Any other advice, tips or tricks...

Nothing exciting but the BH5 QB forum has been sloooow. I assembled both the struts. Pretty straightforward. Tomorrow we will start the brakes. Hopefully it will be on wheels by Black Friday. Building it with my 81 year old dad!

I expect my BH 5 kit in late June. Although it will be ready late this month I won’t be. It was initially scheduled for late July. Since nothing comes early I figured I had plenty of time. Any advice on things I should order now? Parts, tools? Thanks​