Recent content by gregc

  1. gregc

    Thoughts on "less expensive" hardware?

    I hate to say it but given the total cost to build a Bearhawk in 2026 I'm not sure it's worth even thinking about the cost of hardware. A quick look at the BearhawkAircraft site shows that a more or less standard configuration 4 place kit with a new engine costs ~$275,000. Even a $5000 savings...
  2. gregc

    Looking for advice for new plane adjustments

    More on the heavy wing - - Per the link above, if the the aileron attach bracket holes are not perfectly aligned when match-drilled to the aft spar, one aileron may be slightly higher or lower that the main wing. Use a straight edge on the bottom of each wing to look for differences. Try the...
  3. gregc

    O360 Mixture control Bearhawk 4

    The cable setup is the first thing to check and two people makes it easier. Have someone move the mixture control on the panel while you watch what is happening at the carburetor end. You want the mixture lever on the carburetor to be at the end of its travel in the rich direction when the knob...
  4. gregc

    New member seeking a flying Companion F/S

    I sent you a DM - Greg
  5. gregc

    AN Fuel Fitting torque?

    Tight but not too tight ;). Jared is right. the vast majority of AN fittings work fine the first time within a pretty wide range. If not, you can try tightening them a bit. If that fails,you can swap it out.
  6. gregc

    Looking for advice for new plane adjustments

    It's easy to go in circles on rigging problems. I found Nev's build log to be helpful in that his write up is methodical and step wise. https://webuildplanes.com/neville/p/3203/rigging-the-bearhawk- I also found that a cross line laser level helped a lot when I was trying to confirm the...
  7. gregc

    Cowl exit

    Mine is only about 1.5" and roughly 30 degrees. It works fine. CHTs on an O-360 are 350 degrees or less. I think the cowl opening size is much more important.
  8. gregc

    QB - Companion - The Flying Mechanic

    I have no interested in doing so but If I were going to add a rear seat to my Companion it would probably be some sort of lightweight, easily removable jump seat for the rare occasion that I wanted to transport a third person. In that case I would focus first on how to mount it and what sort of...
  9. gregc

    Toe-in and Toe-out - what are your thoughts on Jonas Marcinko video

    Too many differences between a physically constrained model on a treadmill and an actual moving airplane to draw any conclusions.
  10. gregc

    Fuel Flow Transducer

    At least with a Garmin system, If you don't have a straight section on each side of the transducer, your fuel flow indication will fluctuate a lot. I have mine on the FWF side, near the bottom of the firewall, more or less in the middle, but my fuel system is the standard gravity feed, no fuel...
  11. gregc

    Companion W&B, engine choice

    My Companion, with an angle valve 360 and a fairly light ground adjustable prop, has an empty weight CG of 14.6. Pretty much the middle of the 11.9 to 19.8 limits. Since the people/fuel/baggage Arms are all positive, it's the aft limit that matters and a heavier engine/prop combination is...
  12. gregc

    Alaska bush wheel alternative, shaved UTV tires and beadlocks?

    I have been running them successfully at 15 psi as well.
  13. gregc

    Elevator balance weight question

    During a pre-flight today I heard a little knock when moving the elevator. Further investigation indicates that the lead weight is moving around a little. The plans just show a couple of tabs to secure the lead. I'm pretty sure the kit version is a little different in that there are triangular...
  14. gregc

    GPT Builder Assistant

    That's not really how technology matures. Here is one generally accepted model - there are others. Many technologies never make it to actual productivity.
  15. gregc

    Engine Trouble

    Just adding a bit of documentation to this thread for future reference. I happened across this in an O-360 overhaul manual. The last paragraph talks about paint on the cylinder flanges for Lycoming engines that use hold down plates.
Back
Top