Brake lines

Luke68

Junior Member
I was reading the latest bear tracks about the brake system hardware and it got me thinking, why couldn't I use flexible brake lines like in my friends RV? Less fittings to leak, lighter and possibly cheaper.
I looked it up in Spruce and for the NSR tubing ( rated for 2500 psi) and all the fittings would cost around $65. I did some checking and the 1/4" tubing will just slide through a 3/8 aluminum line so my plan is to use that as sort of a conduit through the gear leg so I could also eliminate the need for inspection covers.
Looking for some opinions.
Thanks
 
There's a conversation on here somewhere about brake line types. Based on that thread I ordered premade Aeroquip lines from Summit Racing and am very happy with them. Hope I'm just as happy when I actually start using them.
 
After spending hours researching this topic on line (research includes vansairforce.com) I came back around to what the recent Breatracks article outlined except for making my own flexible hoses using Areoquip 303-4 on the Pressure side of the Master Cylinders. Whee, I am interested in hearing the results of your research and details of your choice of Hoses, and Summit Racing's product offerings.

When I draw a conclusion, I keep an open mind and an eye out for improvement ideas, because I know they exist. So, I am interested in Whee's Choice. He researches things in depth, and draws good conclusions.

Why I rejected the Racing Products was because the Aeroquip 303 hose is an approved industry standard, I can make them myself in the shop with inexpensive tooling, and doing so saved enough money to provide a large enough reward over having an unapproved, but maybe superior stainless branded PTFE hose. I choose to use Rigid Line where the Article suggest because of its weight, cost, durability, and I think ease of fabrication. Most Flex hose I saw had a 5 year shelf life.

I also was aware that our AN fittings are Aluminum, and I have concerns about dis-similar metal corrosion with fittings that are non approved and non-aluminum. But, the Areoquip fitting are not aluminum, so I am inconsistent. I decided that if they are an FAA approved industry standard, then I will turn my head and pretend it will be ok.

As for the light weight plastic hose that Vans uses, I may use a plastic hose product with brass compression fittings for the flexible line that goes from the firewall to the Master Cylinders if I cannot use a reservoir at the Master Cylinder. I have concern over the space available between the rudder pedals and firewall.

I also think the right plastic line has merit on the pressure side, but will require more attention to maintaining, and periodic hose replacement. Lots of Van's Builders have reported poor service results form using the plastic. Consider using fittings that are not plastic.

Brooks Cone
Patrol #303
Shop comes first
Kit Comes next
Meanwhile I research and make plans.
 
When I install the brake system on my BearHawk, it will be my first experience with aircraft brake systems. But I do have many decades of doing brake systems for road racing brake systems.

When I started installing brake systems, I did it very close to what is recommended for the BearHawk. Over the years, I changed to using Aeroquip lines from the master cylinders to the calipers with the fewest number of fittings possible. Each fitting is a potential problem and fewer is better.

I have cars that have been raced since I built them 25 years ago with no brake line issues except for the occasional crash. The few repairs that have been made are frequently nothing more than adding a union in place of a damaged spot in the line.

I plan to use Aeroquip throughout the brake system on my project. The one thing I am going to do is cover the lines with heat shrink tubing to add an extra degree of protection for both the lines and the parts the lines are close too. Having the lines made by a shop like Summit Racing that can install crimped fittings, is much less expensive that buying the reusable fillings. I frequently use a combination of both crimped and reusable fittings.

AN type fittings are available in -3 and -4 sizes in both steel and aluminum.
 
Yep should have done a search first, thanks
No problem, if it hadn't been so late I would have look the thread up for you but I think I was half asleep when I responded. I never hurts to rehash something like brake systems.

After spending hours researching this topic on line (research includes vansairforce.com) I came back around to what the recent Breatracks article outlined except for making my own flexible hoses using Areoquip 303-4 on the Pressure side of the Master Cylinders. Whee, I am interested in hearing the results of your research and details of your choice of Hoses, and Summit Racing's product offerings.

When I draw a conclusion, I keep an open mind and an eye out for improvement ideas, because I know they exist. So, I am interested in Whee's Choice. He researches things in depth, and draws good conclusions.

Why I rejected the Racing Products was because the Aeroquip 303 hose is an approved industry standard, I can make them myself in the shop with inexpensive tooling, and doing so saved enough money to provide a large enough reward over having an unapproved, but maybe superior stainless branded PTFE hose. I choose to use Rigid Line where the Article suggest because of its weight, cost, durability, and I think ease of fabrication. Most Flex hose I saw had a 5 year shelf life.

I also was aware that our AN fittings are Aluminum, and I have concerns about dis-similar metal corrosion with fittings that are non approved and non-aluminum. But, the Areoquip fitting are not aluminum, so I am inconsistent. I decided that if they are an FAA approved industry standard, then I will turn my head and pretend it will be ok.

As for the light weight plastic hose that Vans uses, I may use a plastic hose product with brass compression fittings for the flexible line that goes from the firewall to the Master Cylinders if I cannot use a reservoir at the Master Cylinder. I have concern over the space available between the rudder pedals and firewall.

I also think the right plastic line has merit on the pressure side, but will require more attention to maintaining, and periodic hose replacement. Lots of Van's Builders have reported poor service results form using the plastic. Consider using fittings that are not plastic.

Thanks Brooks, though I sure that there are many that disagree with you about my decision making.

Anyways, when was looking into brake lines I had talked to people about about the small plastic lines, standard aluminum lines and Aeroquip lines. I never could get comfortable with the plastic lines though I know some here have used them with good success. I've been told they need to be replaced every 5 years or so because they do age and can break. I intended to go with standard aluminum lines until two people I trust gave me a strong recommendation for Aeroquip lines. All the reviews I could find about the premade Summit Racing lines were really good, S Lathrop as an example, and I figured professionally made racing lines would be better than aircraft lines that I made myself. That may or may not be true but the lines from Summit are great quality. I know of a couple other airplanes that have used the premade lines from Summit and the owners are still happy with them.

I went with -3 hoses; they have steel fittings and are tested to 4000psi. Lots of different sizes available from Summit: https://www.summitracing.com/search...ch&SortOrder=Ascending&keyword=aeroquip brake

I had planned to go with a firewall reservoir but when looking on Aircraft Spruce for the a reservoir I came across their master cylinder mounted reservoirs. They are fairly inexpensive so I tried them and I think they will be great.
 
Having looked around online extensively before I made my choice, most Bearhawk builders (judging by the records available on build logs, photos, etc.) seem to use a mix of aluminium hard line, Aeroquip hose, and plastic soft line all together. That is what I did.

Using a flexible Aeroquip 303 or similar is the most expensive but is less likely to fail - but it does fail sometimes, I cite a recent local crash. The plastic line is the lowest cost solution, but requires replacement after a time, albeit it very infrequently - but it will fail eventually if not replaced. The hard line is obviously good for the life of the aircraft and is cost-effective, but cannot be used around the gear leg interface or pedals. Some don't like hard line at the caliper, although it is commonly used there with no issues yet AFAIK.

I used hard line and soft line throughout the fuse, aeroquip 303 at the gear leg to fuselage interface, and hard line in the legs. Provided you use good quality brass fittings to interface with the plastic,, it works really nicely (touch wood). Obviously it has a limited life, and you will need to spend an hour or two replacing it every 10 years or so (less if it sees any regular direct UV light). I used hard line at the calipers with a protective pastic sheath wrapped around the aluminium. Initially, I had my doubts about using aluminium near the calipers, but now I can tell there's not enough movement there to cause the aluminium to work harden. We land in the roughest of stuff, and those lines are not seeing any undue wear.

Using Aeroqip line everywhere is the Rolls Royce solution. Using plastic line everwhere is the normal LSA solution. But personally, I would not put plastic line anywhere you can't easily replace it.
 
Last edited:
My A&P/IA friend is constantly showing me examples of "engineering decisions that complicate maintenance"... Look at any Mooney for prime examples (you remove something like 100 screws to get full access to the engine), but there are dozens of other examples on every plane ever built. He's shown me a couple of cases where they had to almost completely disassemble structural elements to gain access to non-structural items like servos. Absolutely crazy!

So, I made a promise to myself that I would build as light as possible, consistent with easy maintenance. If it comes down to adding weight or "complexity" during the build process to make maintenance afterward easier, ease of maintenance wins every time.

To me, brake reservoirs mounted directly on the master cylinders fall into the "increased complexity / difficulty of maintenance" down the road. Trying to reach into the cockpit from outside, or contort myself to get under there to check the level and/or refill a brake reservoir is pretty challenging for me today, at age 60. How much harder will it be when I'm 70? Will I really do the "contortion" routine on every pre-flight to check those fluid levels? No? Didn't think so... So no cylinder-mounted reservoirs for me - I'm putting mine on the engine side of the firewall, where I can reach it easily when the cowl is open, and check it on every pre-flight. Just my 3⍧ worth (inflation).

As for plastic versus aluminum versus Aeroquip-type lines, I'm inclined against using plastic, just because I know it will be a pain to have to replace them every 5 years, and they do become brittle after some time passes. I like the simplicity of the Bob-style aluminum lines, but worry about the flexing they will do at the rudder pedals and where they exit the fuselage to the landing gear legs. At least those two sections will be flexible braided Aeroquip-style, and If I'm doing that much, why not all of it? I guess cost will be my guideline on that decision...

PS - thanks for the link to Summit Racing's page. Now I'm looking at their "standard lengths" to see if I can design my layout to take advantage of using their "standards" - which cost less than "custom" work... Lots to think about!
 
My RV friend also used aluminum at the calipers but he made a loop to take up any movement from the calipers, did you do the same or just run it straight out?
 
Trying to reach into the cockpit from outside, or contort myself to get under there to check the level and/or refill a brake reservoir is pretty challenging for me today, at age 60. How much harder will it be when I'm 70?
I am 32 and getting under the panel to the pedals is a pain in my, well, in everthing!! It's just the worst place in the whole plane to access.
I think only children would be comfortable working in those cramped spaces.

When I change my plastic lines, I will drop out the tunnel (5 minute job) and then have full access from underneath, while sitting on a short-legged stool.

If you are installing a parking brake (personally I think every real aeroplane should have one for safety's sake) then you have a handy termination point for the flexible hose from the pedals. You can run aluminium line from there to the bulkhead under the floor, flexible to the top of the leg, and then aluminium hard line down the leg.
 
Last edited:
Luke68
Here is the S bend:
IMG_20160708_125628_zpsimyukpfj.jpg
 
I have always set up my planes the same - and of course think this is the best way. Plastic lines from the fluid reservoir on the firewall to the master cylinders (no pressure), then the Aeroquip made up lines from the master cyls to the fuselage/gear leg intersection, then hard aluminum lines down to the brake caliper. Has worked well for me all these years. I have never had to replace anything. N303AP has over 1,100 hours.

I have personally seen plastic/nylon lines fail twice (once on Patrol & once on an RV) when used in the high pressure areas. Theoretically they should handle the pressure fine. But I have seen them fail twice. Mark
 
If you are installing a parking brake (personally I think every real aeroplane should have one for safety's sake)

Not intending to steer the conversation away from brakes lines, but I have been wrestling with this decision for a while. Can you elaborate Jon? I've owned 3 airplanes without parking breaks and never missed them, but I also don't have the bush experience that you have, and that's how I hope to use my 4-place. I've only considered parking breaks something that holds the airplane still from the time you get out until you slip the chocks in. Obviously they increase cost, weight complexity. What am I missing?
 
I would have to agree with Mark, I used plastic on my first 2 homebuilts but changed after a messy, inconvenient failure. I use 3/16 alum and -3 Earl's SS braided teflon. The aluminum can be coiled at the caliper to allow movement. The earl's hose is light and fittings are reusable and compatible with AN tube fittings.
 
Hey Jim, How's "the bird"? ;-)

Wondering just where your plastic failure was and how it happened. Did you have failures on both planes? We have used plastic on the whole system and it's a bit late to change it now, so I'll have to keep a close look out for any beginning failures I guess. Donna
 
Hi Donna,
Tweety has been tucked away in the hanger for the last week due to weather, but is doing very well. I flew it up in the mountains last week with 2 185 lb guys on board and got up to 12.5k ft without too much effort. Everybody seems to love that airplane.


I only flew my first homebuilt about 20 hours after I converted to hydraulic brakes. My failure was about year 3 on my Rans S7. The plastic line pushed out of a fitting (brass) when I applied the parking brake. The fitting was properly made up with tube inserts, but the plastic creeps a little over time. Rans supplies all SS braid teflon for brake lines on the current line of kits.

Waiting for your first flight reports.

Jim
 
Aaw Jim ya just made me cry. This is the 4th time that's happened since we started this adventure. I expect 1 more time after first flight--tears of joy!!! ( I miss that bird! When the time comes and if I have won the lottery, will ya sell her back to me?? ). D.
 
I have personally seen plastic/nylon lines fail twice (once on Patrol & once on an RV) when used in the high pressure areas. Theoretically they should handle the pressure fine. But I have seen them fail twice. Mark

You've told me before, but I forget - did the actual plastic tube fail in some way, or was it the end fittings which let go?
 
I snapped a pic of my pedals with some of the Aeroquip hoses and one reservoir installed. I completely agree with making the airplane easy to maintain. I don't have any trouble reaching theses master cylinder mounted reservoirs. I don't have any real experience flying a airplane equipt with hydraulic brakes so I don't know how often the fluid should be checked but I can say that when I've flown with others they didn't check the brake fluid level.

b3f946ddbce4dcf9a37cf42e0049e231.jpg
 
I don't have any real experience flying a airplane equipt with hydraulic brakes so I don't know how often the fluid should be checked but I can say that when I've flown with others they didn't check the brake fluid level.
I have clear lines from my reservoir to my cylinders like Mark does. I check the fluid level EVERY time before I land by looking between my feet, its part of my GUMP / BUMP check. If I see pink in the tubes, I know I have a green-light for braking during landing.
If one of the brakes has leaked down, I want to know before I cause a ground loop. I know a lot of people who've written off planes when one brake failed. I figure this check it could save my plane one day. It also mitigates the risks of the plastic tube failing - at least I can see the failure.
 
Last edited:
I have clear lines from my reservoir to my cylinders like Mark does. I check the fluid level EVERY time before I land by looking between my feet, its part of my GUMP / BUMP check.

I had master cylinders with built-in reservoirs on my Pacer and never thought about checking brakes other than observing their operation on taxi. One day I do a wheel landing and as the aircraft slows down I try using a little right brake to help with keeping her straight. The pedal goes all the way down with no resistance and I end up ground looping. Post flight reveals very low fluid in the cylinder and I was able to "pump up" the brakes to work again, which I believe means air was in the lines. Amazingly, the only damage was to the drooped wing tip but it could have been a lot worse. I had not realized the safety implications of Battson's setup but now that I do I will copy him.
 
In one incident heavy braking melted the plastic line going to the caliper (RV). And the other incident was a Patrol where the line rubbed and developed a BIG leak. Luckily, it was at my ranch and I had the fittings and line so the owner could make a provisional repair to get home. Mark
 
I check the fluid level EVERY time before I land by looking between my feet, its part of my GUMP / BUMP check. If I see pink in the tubes, I know I have a green-light for braking during landing.
That's a great idea. I'm surprised that you can see the lines while flying though. We are similar height and the only what I'd be able to see my feet is if I slid my seat back. But those plastic lines do provide the opportunity to check fluid level during preflight.
 
A guy I know did significant damage to his Grumman Traveler (not once, but twice!) because he did not / could not check his brake fluid level. That airplane has castering nose gear (like an RV) and relies on differential braking for directional control on the ground. The first time, he wound up running the plane into the side of a hangar, damaging the left wing only. The second incident was much worse, as he ran the prop and right wing into a parked Mooney – absolutely totaled that airplane, and did $40K worth of damage to his own plane (worth about $50K at the time).

I think I'm going to follow Mark's example the brake fluid reservoir attached to the engine side of the firewall, plastic tubing to the "reservoir" side of the master cylinders. Then Aeroquip lines to the parking brake valve, hard lines from the valve to just inside the gear leg attach point, Aeroquip lines for that "flex" connection. The gear legs will have hard lines inside the "faired" area of the gear, and Aeroquip to the brakes themselves. I'm going to use a clear brake fluid reservoir (ACS) so that I can easily check the fluid level on every pre-flight, and I like Battson's idea of visually checking the line between the firewall and brake cylinders for visible brake fluid before applying the brakes. I'll have to add that to my checklist, and figure out a way to rig a mirror or something to avoid contorting...

Man, I love these forums!
 
I'm surprised that you can see the lines while flying though. We are similar height and the only what I'd be able to see my feet is if I slid my seat back.
You do have to lean over sideways a few inches, but it's not too hard to see under there. But that said, I do have relatively long legs and a short torso!
 
You do have to lean over sideways a few inches, but it's not too hard to see under there. But that said, I do have relatively long legs and a short torso!

Thats the difference; I have short legs and long torso. Another thing is I like sitting really far forward.
 
I have always set up my planes the same - and of course think this is the best way. Plastic lines from the fluid reservoir on the firewall to the master cylinders (no pressure), then the Aeroquip made up lines from the master cyls to the fuselage/gear leg intersection, then hard aluminum lines down to the brake caliper. Has worked well for me all these years. I have never had to replace anything. N303AP has over 1,100 hours.

..... Mark

Digging up an old..ish post......

When hard aluminum tubing is from the top of the landing gear leg, all the way down to the caliper, verify for me what type of aluminum tubing is typically used...... I am looking at Aircraft Spruce, specifically, I don't want to assume, but are we talking about 5052-0, 1/4 inch, .035" tubing?

Maybe 1/4" 3003-0 soft flexible Versa Tube?
 
Either would be OK. But I would use 5052 here. And the line does not straight to the fitting on the brake caliper. You make a little curve so the line can flex some. Mine is kind of a half loop right up to the caliper fitting.
 
5052 - 7 years no problems but you've got to have a stress loop in it like Mark describes. Otherwise a short flex line.
 
I will pass on my experience with brake lines from 40 years of building race cars. Now the line pressures in race cars are way higher than an airplane. Vibration frequencies are much higher but no where as long as in an airplane.

What I found was I had more issued with connections. So I worked to minimize the number of connections between the master cylinders and the calipers. I ran -3 braided lines from the master cylinder to each front caliper and at the rear I ran the same lines to a tee, then to each rear caliper.

Now it is common for the front suspension to run a line from the master cylinder, through a tube built into the front lower a-arms and then to the caliper. I have been thinking about doing this on my 4 place brake system. The tube would be in the gear leg so replacing a worn line would be quite simple. I have not cut metal on this idea. Frequently the lines in the a-arms are -2 size.

Just throwing out the idea for input.
 
I hear several people in different threads as well saying that 5052 is preferred over the versa tube. Is there any reason the versa stuff would not be fine for the gear legs? I don't have a tubing bender yet so I figured I'd use versa here... Thx
 
I have used the 3003-0 versa tube in the gear leg with no problems. I think 3/16" is adequate...more flexible than 1/4" . The loop at the bottom is important for the calipers to move. I like to exit the brake line on the bottom of the gear leg and loop it around the back side and up to the brake fitting.
 
I need to add to this post - a caution:

Following maintenance of our plane, I had new calipers installed and needed to brake continuously and heavily for many minutes to wear the calipers in.
During the maintenance, I tightened all the brass end fittings on the PLASTIC brake lines around the pedals (only place I have plastic hose is around the pedals). But there was one fitting I couldn't reach.

During the ground braking work, I pressed especially hard and blew the plastic hose out of the brass end fitting. This caused an instant loss of brake control on one side, and a bit of a mess to clean up.

I have say, even at taxi speeds blowing a brake hose makes the plane hard to control. During a landing roll, there would be a high risk of ground-looping if you had an instant loss of brake pressure.
 
Hi Guys,

my plane's progressing along nicely, the brakes are installed, and I've routed the flex lines between the LH and RH brakes. Now I need a bit of guidance:

1) Every builder I've seen on this forum has pilot's and copilot's brakes set up as a pair, "in series" - e.g. the bottom of the pilot's LH master goes to the top of the copilots LH master, and the bottom of his RH goes to the top of the copilot's RH master. In my set up, the two inboard pedals supply the two outboard pedals via crossed tubes, and then the flex lines to each MLG assy run straight from the outboard pedals. Mathematically, it gives the same outcome, and it saves two extra brake lines crossing the cab, but is there a reason this setup should be avoided?

2) Can someone (or many of you!) supply me a good photo of how the flex lines run from the pedals to the MLG assy? I haven't built the tunnel or floor sections yet, and I'm not sure how the line "pops out" of the fuselage and into the elbow between the gear attach lugs. I need to go through the bulkhead under station B, but there won't be a bulkhead fitting. If there's a particularly good routing solution, I'll get Jared to add it to the bearkhawk tips (with the owner's permission, of course).

Thanks guys, it's great to be able to connect with people on this forum, makes your little project feel like part of something big and exciting :-)

James
 
Found some useful photos myself, in case anyone else is looking:
Battson and Blackrock have both posted photos from underneath their planes on thread number 21615 (you can just "search" these thread numbers, goes straight to it!)
This shows how this part of the brake line can be routed. Seems like having a 90 degree bend before the MLG swingarm is popular.

Because I won't have a bulkhead fitting on the aluminium under station B, I'll make up a 90 degree bracket and a P-clamp for support.

James
 
I was looking for something else on a vendors website and came across, by accident, some brake reservours that mount to directly to the caliper. I remember Whee saying he used something similar but it didn't click then. It does now. 25 bucks each. For a dual brake system, you would still only need 2. Cuts down on brake lines/complexity. The only downside I see is you can't visually inspect the fluid level, but with fewer connections, there is less of a chance for leaking and checking the level becomes less important.

Especially since the brake lines move a lot with the rudder pedals, and take a bit of were and tear.

Anybody else use them?
 
Mine are still working good. I don't see need to check the fluid every flight but it isn't hard for me to unscrew the caps and check the fluid level when I have reason to.
 
Mine are still working good. I don't see need to check the fluid every flight but it isn't hard for me to unscrew the caps and check the fluid level when I have reason to.

I have been in the habit of checking every flight before takeoff and landing, by glancing at the clear plastic tube.
The other week I noticed one side had bled down to the caliper, no idea where the fluid went. Pumped it back up, pleased to find it before I went flying.
 
I have been in the habit of checking every flight before takeoff and landing, by glancing at the clear plastic tube.
The other week I noticed one side had bled down to the caliper, no idea where the fluid went. Pumped it back up, pleased to find it before I went flying.

Not a bad habit for sure. My first airplane had cable brakes so I have very little experience with hydraulic brakes on an airplane. However, of my little bit of experience flying in friends airplanes and asking around in my small circle of aviation friends none of them have checking the brake fluid on their preflight/post flight checklists.
 
I remember reading earlier in this post about what Whee used. It didn't click at the time why he did it. Simpler, fewer connections, 1 less firewall penetration. Probably lighter, and probably cheaper. One less thing on the firewall. I think I am going to throw in with Whee on this one.

At work I never checked brake fluid, only brake wear, either directly or with mechanical indicators. We did have either a brake pressure gauge, or light, to check when you set the parking brake. I may end up with a brake pressure light/sender.

I don't remember ever checking brakes before landing, but my single engine time was very long ago. If I need the brakes, it is probably a really good habit to get into before landing. Hopefully I will remember to put that into my habit patterns.
 
Is firewall clearance an issue for cylinder mounted reservoirs ? It does sound very simple to do. Any other drawbacks besides ability to check fluid levels through a clear tube ? I’ve never checked fluid levels on any aircraft prior to landing etc, but always checked for brake pedal pressure. It probably takes on more significance in a STOL taildragger though. You wouldn’t want the first time you become aware of one brake low on fluid to be when the pedal goes to the floor on a short strip, with hard braking on the other side. I guess the only way to check levels on the cylinder mounted reservoir is to dip them ? Interesting discussion.
 
The firewall mounted reservous that I already bought is black painted metal. You can't see it. I am redoing my rudder cables as we speak (post) and brakes I already started on. There is plenty of room for the A-600's. Not sure of the motorcycle ones but I have seen some pretty small plastic tanks on motorcycles. The A-600 have a 1/8 NPT fitting welded on, I don't see that on the motorcycle parts. I will give it a few days looking for different types.

The A-600 is 1 3/8" (35mm) in diameter 9 (round), and 2 3/8" (60mm) tall. Looks to be plenty of room, you might have to orient the cylinders one way or the other to avoid contact with the firewall station tubing.
 
Good idea. Clutch reservoir might work as well. I have seen some pretty slick little ones on some smaller motorcycles.
 
It seems to me like if a builder wanted to install the A-600 reservoir and get a fluid level indication, one could remove the threaded cap, install a fitting with a clear tube extending out the top of the cap. Maybe even connect the clear tube from one reservoir to the other. I think the system needs to breath though.... Where is the vent in my A-600?
Screen Shot 2020-11-02 at 6.49.41 PM.png
 
Good idea. Clutch reservoir might work as well. I have seen some pretty slick little ones on some smaller motorcycles.

The one I used was all aluminum. IIRC, it had a 1/8 pipe thread for the outlet fitting. I actually had to plug the existing one and drill/tap a new outlet so the site glass was where I wanted it for the side of the firewall it was mounted on.

Far less work than making one and pretty inexpensive.

Definitely wouldn't go with a plastic one.

But each to their own.
 
I am going to look for a few days in ATV/motorcycle/etc but the fittings are wrong for mounting into the 1/8 NPT brake cylinder. The A-600's are pretty cheap. If I wanted a sight glass I think you could cut a vertical slot in the front and back of them, and bond some plastic tubing over the whole thing to seal it. A flashlight should allow preflighting fluid level.

Declutters the firewall area, and reduces fittings and weight.
 
Yeah Whee - you've answered a question I tried to ask elsewhere - you've connected your brakes L-L, R-R with a crossed line in the middle - did this setup work ok for you mate? That way, you've got the RH and LH flex lines to the wheels already on the outboard side of the outer pedals. :-)

James
 
Is firewall clearance an issue for cylinder mounted reservoirs ? It does sound very simple to do. Any other drawbacks besides ability to check fluid levels through a clear tube ? I’ve never checked fluid levels on any aircraft prior to landing etc, but always checked for brake pedal pressure. It probably takes on more significance in a STOL taildragger though. You wouldn’t want the first time you become aware of one brake low on fluid to be when the pedal goes to the floor on a short strip, with hard braking on the other side. I guess the only way to check levels on the cylinder mounted reservoir is to dip them ? Interesting discussion.

I can't comment on reservoirs, however I can say my toe-brakes can all touch the firewall when you brake hard at full rudder lock. This is not an issue.
 
It seems to me like if a builder wanted to install the A-600 reservoir and get a fluid level indication, one could remove the threaded cap, install a fitting with a clear tube extending out the top of the cap. Maybe even connect the clear tube from one reservoir to the other. I think the system needs to breath though.... Where is the vent in my A-600?

The red plugs come with a small hole drilled in them; that’s the vent.

I can see several options for adding a sight gauge if you wanted one. Perhaps the easiest would be a short price of clear PVC pipe screwed in where the red plugs are. Then just fill the reservoirs through the pvc pipe until they are a certain height in the pipe. Then put a drilled cap on the end of the pipe.
 
I got my ACS A-600's yesterday. 2.8 ounces each. I weighed the Matco part, 2 pre-made Summit -3 brakes lines and adapters. The A-600's are about 4 oz less, cheaper, eliminate several fittings that could leak, and declutter both sides of the firewall. Hopefully I can use the Summit lines for the parking brake. Doing all that now.
 
I installed a set today. At the same time I moved my parking brake off the firewall. The result is a much cleaner setup with fewer lines.

Click image for larger version  Name:	IMG_1737.jpg Views:	0 Size:	1.40 MB ID:	59276Click image for larger version  Name:	IMG_1740.jpg Views:	0 Size:	1.90 MB ID:	59277


A couple of pictures. I mounted the parking brake to the bulkhead at B. Flexible lines from the master cylinders to right angle bulkhead fittings and then hard lines to the brake valve. The copilot side goes directly to the flexible line that goes to the gear leg. The pilot side needs a 180 degree loop first. The bracket acts as a doubler and provide the attachment point for the push-pull cable. The only real drawback I see is that i will have to remove the floor or add an access panel for maintenance on the brake valve.
 
Last edited:
One of the factors that isn't that intuitive is that any type of brake line attached to the caliper rotates and moves in an arc. When you tighten the fittings, the lines are fixed. They don't allow for the line to rotate, unless there are some swivel fittings folks use that I am not aware of. I am sure somewhere they exist. Putting loops, or a big arc in the line, will help to minimize stress on the lines at the fittings.

The fittings at the top rotate, and move in about a 40-50 degree arc over 2-3 inches. The lower fittings rotate the same, but only move an inch, maybe a bit less. No matter what you do to the upper fittings, unless you have some type of swivel fittings, there is quite a bit of stress on the line, at the fittings. The A-600's eliminate that problem.
'
The lines going into the lower fittings move quite a bit less. Not as much of a problem.

Like Whee said, there are several ways to add a sight gauge. But those also create more failure points. I will think about it, but for now I am happy to reduce failure points, and check brake fluid level occasionally.
 
Yes, master cylinders at the pedals. The upper fittings move a LOT. Upper and lower rotate about 40 - 50 degrees as well, but once you cinch up the fittings, the lines are fixed. I only found one routing that I liked, and I wasn't in love with it.

I am only using brakes on the left side. It gets pretty tight with parking brake lines (in and out), and lines from the reservoir on the same side. It is a little easier with brakes on both sides as you can put the reservois on one side and the P brake on the other.

I personally like the A-600's and am going to use them.
 
Back
Top